CNC router · Wisconsin
CNC router repair in Wisconsin
Routers for cabinets, furniture, signs, plastics and aluminum repaired on site: spindles, vacuum hold-down, gantry drives and racks, tool changers and controls.
What we fix
- Spindle noise and heat
- Weak vacuum hold-down
- Gantry racking and drive faults
- Tool changer misses
- Control and homing problems
Techs from the Milwaukee, Madison and Green Bay regions.
Quick answerLocalSpindle of Wisconsin repairs CNC routers across the state, including MultiCam, Thermwood, Biesse, SCM, Homag, CR Onsrud, AXYZ, ShopSabre and Anderson. We fix router spindles, vacuum pumps and tables, gantry drives and rack and pinion, tool changers, dust collection interlocks and controls.
From our techs
Wisconsin's router shops
Wisconsin has a deep woodworking and cabinet industry, and plenty of plastics and sign shops, so routers are everywhere. They run fast and long, in dust that finds its way into everything. The most common calls: spindles getting noisy, parts moving on the table because vacuum is weak, and gantries that rack or lose steps.
Router spindles are high-speed and sensitive to dust, collet wear and crashes. We check runout, collets and tool holders, temperature and noise, and rebuild spindles when bearings are done.
Vacuum, gantries and changers
Weak hold-down is usually leaks: a worn spoilboard, gaskets, valves, or a vacuum pump that’s tired or needs service. We test vacuum at the pump and the table to find where it’s going.
Gantries with two drive motors need to stay square. A gantry that racks after a crash or loses position at speed has a drive, rack, pinion or coupling problem. Tool changers on routers jam on dust and worn pockets. We clean, adjust and replace what’s worn.
Symptoms
What you're seeing, and what it usually means
The alarm names the axis or the unit. These are the causes we find behind it most often.
| What you’re seeing | What it usually means |
|---|---|
| Parts shift during the cut | Vacuum leaks, a worn spoilboard or a tired vacuum pump. |
| Spindle loud or hot | Bearings, collet problems or dust contamination. |
| Gantry out of square | Crash damage, a slipping pinion or a drive fault. |
| Steps lost at high speed | Drive tuning, loose couplings or worn rack. |
| Tool changer jams | Dust, pocket wear, air pressure or sensor problems. |
| Machine won’t home | Limit or home switch, wiring or a drive fault. |
How we work it
CNC router: our approach
Spindle and collets
Runout and condition.
Vacuum
Pump and table tested.
Gantry
Square, drives and racks.
Run a job
Cut quality and accuracy checked.
A full visit
What a visit can cover
- Spindle runout, collets, temperature and noise
- Vacuum pump, valves, gaskets and table
- Gantry square, racks, pinions and drives
- Tool changer, pockets and sensors
- Dust collection interlocks
- Lubrication of rails and racks
- Controls, homing and limits
- Electrical cabinet cleaning
On the van
- Vacuum gauges
- Indicators and squares
- Meters for drives
- Common sensors and gaskets
- Collet and holder checks
Example service call
Cabinet shop router losing hold-down on small parts
The call
A cabinet shop in Marathon County had small parts shifting during nested cuts on a router that used to hold them fine.
What we did
- Phone. We asked about spoilboard condition and vacuum reading. The gauge was lower than usual.
- On site. The spoilboard was worn thin in spots and a zone valve gasket was leaking.
- Fix. Replaced the gasket, serviced the vacuum pump and recommended resurfacing the spoilboard, which the shop did.
- Check. Vacuum back up and small parts held through the nest.
The result. Nested jobs ran without shifting parts.
A typical call, written to show how we work. It isn’t a specific customer.
Talk to a Wisconsin tech
Same problem on your floor?
Call and a tech will tell you what we’d check first, then the closest team heads your way.
- You talk to a tech, not a call center
- The closest Wisconsin team takes the job
- Straight answer on repair, rebuild or replace
- Haas
- MultiCam
- Thermwood
- Biesse
- SCM
- Homag (Weeke)
- CR Onsrud
- Komo
- AXYZ
- ShopSabre
- Laguna
- Anderson
- Morbidelli
- Holz-Her
- Felder
From the field
CNC router: tips from our techs
Resurface the spoilboard
Worn spoilboards leak vacuum. Resurface on a schedule.
Blow out the cabinet
Dust in the electrical cabinet causes heat and faults.
Check collets
Worn collets hurt finish and spindle life.
MultiCam, Thermwood, Biesse, SCM, Homag, CR Onsrud, Komo, AXYZ, ShopSabre, Laguna, Anderson and others.
Yes, pumps, valves, gaskets and tables.
Yes, after a crash or as maintenance.
Yes, as part of a maintenance plan.
Who comes out
Wisconsin teams for cnc router
The founding team closest to your shop takes the call. Central and western Wisconsin calls go to whichever team is nearest.
Milwaukee
Southeast Wisconsin. Cnc router calls in Milwaukee, Waukesha, New Berlin, Menomonee Falls, Germantown, West Allis and nearby towns.
Madison
South central Wisconsin. Cnc router calls in Madison, Sun Prairie, Middleton, Janesville, Beloit, Watertown and nearby towns.
Green Bay
Northeast Wisconsin and the Fox Valley. Cnc router calls in Green Bay, De Pere, Appleton, Neenah and Menasha, Oshkosh, Fond du Lac and nearby towns.
Keep reading
Related repair
Machine down?
Get your CNC router sorted
Call and talk to a tech about the machine, the control and the symptom. The Wisconsin team closest to you takes it from there.
